• Dear customer Congratulations on your choice! Your Bernette Funlock 004D/004 is made to the highest standards. It will cut, sew and neaten for you in one smooth operation giving a professional look to anything you make. Diver T Program Dallas County. Certified Scuba Diver FEMA. The 2011 Chair Academy International Leadership Conference Hosted by the Dallas County Community. The Dallas Initiative for Diversion and Expedited Rehabilitation and Treatment (DIVERT Court) is a program available for Dallas County residents in efforts to enhance. Collin County; Community. Dallas County's DIVERT program provides intense supervision in. Chavez’s attorney got him into Dallas County’s DIVERT program. Community Resources. Dallas County Juvenile Department believes that for. Diversion programs offer youth an opportunity to agree on voluntary conditions. Diver t program dallas county community. FOOT CONTROL PEDAL W/ Cord Bernina Bernette Funlock 003 004 004D 006 006D 007D + Bernette Service Manual for FunLock 004 Serger KNIFE Lower Blade Bernina. The 4 thread Bernette Funlock is particularly suited to sewing stretch fabrics. Let your wardrobe and home benefit from the Bernette’s superb sewing qualities. • Retyped by Mastersewusa.com Contents Safety regulations Contents Details of the machine Setting/Practical sewing ● Accessories ● Presser foot pressure ● Roll hemming ● Sewing in tape Preparing the machine ● Thread breakage, unpicking seams ● Foot control ● Assembling the thread stand Maintenance ●. • Retyped by Mastersewusa.com Details of the machine Details of the machine 1. Looper cover 2. Looper cover opening indent 3. Knife guard 4. Cloth plate opening lever 5. Cloth plate 6. Stitch plate 7. Presser foot 8. Lower looper thread tension dial 9. • Details of the machine View with looper cover open 1. Upper looper 2. Upper knife 3. Lower knife 4. Selection lever for overlocking or roll hemming 5. Lower looper 6. Lower knife setscrew View with cloth plate open 1. Cutting with adjustment knob 2. • Preparing the machine Attaching the foot control Plug foot control into machine socket (A) and then into main socket (B). The foot control regulates the sewing speed. The sewing speed can be adjusted by increasing or decreasing the pressure on the foot control. Thread guide Raise, the support rod fully, turning slightly until the positioning catches engage (C). • Preparing the machine Thread cones/spools The anti-vibration cone should be used with the wider edge at the bottom on the spool holder pin when sewing with cones. Large spools If large industrial spools are used, position the anti-vibration cone upside down on the spool holder pin, i.e. With the wider edge at the top. • Using the machine Power/light switch The power/light switch is conveniently placed on the hand- wheel side of the machine in front of the socket. • Off (A) • On without light (B) • On with light (C) Handwheel The handwheel turns forward, i.e. In the same direction as on a household sewing machine. • Using the machine Two-step presser foot lifter To raise the presser foot, raise the presser foot lever on the rear of the machine, until it engages (A). It can be raised again to maximum height and held in this position to provide more space between presser foot and stitch plate (B). • Using the machine Inserting the needles Needles can be inserted quickly and easily with the practical brush-cum-needle inserter (A). • Turn power switch to “O”. • Turn handwheel towards you until needles are fully raised. • Lower the presser foot. Using the small screwdriver, loosen the needle set- screws and remove the needles (B). • Threading Preparation/Tips • Turn power switch to “O” • Support rod with thread guide must be fully raised. • Open the looper cover and cloth plate. • Turn the handwheel towards you until needles are fully raised. • Raise the upper knife. Thread the machine carefully and in the correct sequence. • Threading 1. Upper looper thread, blue markings Place the spool on the spool holder pin underneath the blue marking on the thread guide. (1) Bring thread up from spool and take it through the blue guide. (2,3) Make S-loop around thread guide bar. (4) Thread guide. • Threading 1. Lower looper thread, red markings Place the spool on the spool holder pin underneath the red marking on the thread guide. (1,2) Bring thread up from spool and take it through the red guide. (3,4) Make S-loop around thread guide bar. (5) Thread guide. • Threading 3. Right-hand wheel needle, green markings Place the spool on the spool holder pin underneath the green marking on the thread guide. (1,2) Bring thread up from spool and take it through the green guides. (3,4) Make S-loop around the thread guide bar. (5) Thread tension dial. • Threading 4. Left-hand needle, yellow markings Place the spool on the spool holder pin underneath the yellow marking on the thread guide. (1) Bring the thread up from the spool and take it through the yellow guide. (2,3) Make S-loop around thread guide bar. (4) Thread tension dial. • Threading, Trial sewing 3 thread overlock (right needle) For a 3-5 mm wide 3 thread overlock stitch, remove the left-hand needle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |